Homepage

1. Engine Basics

2. Advanced Engine Tuning + Forced Induction

3. EFI Tuning

4. Chassis Tuning

5. Misc. Information

6. WHAT'S HOT in Auto

7. New Products + Tools

8. All Wheel Drive Civic Type RL

Contact Us

 

DOT Help

Department of Transpertation

Reading Spark Plugs

Thanks to Larry Meaux of Meaux Racing for providing this information and pictures.
 

• This is only valid if you shut-off the engine after the finish line then tow the car back to the pits where you remove the plugs for reading !!
• Or if you are on the dyno
• VALID ONLY for full load acceleration or steady state dyno tests

Plugs are best viewed with a 10x power illuminated magnifying glass.
 

• The "Ground Strap" = Heat Range
• The "Plug's Base Ring" = Jetting
• The "Porcelain" = signs of preignition/detonation

---

Heat Range: (click for larger image)

Heat Range = Ground Strap, the ground strap indicates the heat-range of the spark plug. If the "color" of the ground strap "changes" too close to the ground strap's end, (which is above the center electrode), then the heat-range is "too cold" , meaning that the strap is loosing heat too quickly to the base ring, and is not able to burn off deposits until near its end. If the "color" of the strap changes near where it is welded/attached to the base ring (last thread ring), then it means that the plug heat-range is "too hot", because heat is not being tranferred/cooled from the strap to the base ring quickly enough !!!! The strap might begin to act like a "glow-plug", eventually causing preignition and/or detonation later on. Proper heat-range is when the "color" is at the half-way point on the strap, neither too cold or too hot.

(Color= meaning the evidence of heat/or lack of heat by the appearance dark vs lightened color of metal)

---

Jetting:

Jetting = the air/fuel mixture ratio shows up on the base ring (the last thread ring, it has the strap welded to it). You want a full turn of light soot color on the base ring!!! If you want to tune for max. power, then you want 3/4 to 7/8ths of a full turn of light soot color to show up on the base ring, but this is on ragged-edge of being too lean, but will make the most HP on most engines. To be safe, leave it at a full turn of light soot color. If the base ring has a full turn of color, but there are "spots" of heavy build-up of "dry soot" on top of color, then jetting is too rich .

NOTE> If the base ring has a full turn of color with some spots of heavy dry soot, then jetting is too rich, REGARDLESS, if the porcelain is "BONE-WHITE", jetting is still TOO RICH !!! NOTE> Do not look at the porcelain to read jetting !!!

---

Preignition/Detonation

Porcelain = the porcelain shows up preignition/detonation, it will not accurately reveal jetting/air/fuel ratios. To look for the first/beginning signs of detonation, search the white porcelain for tiny black specks or shiny specks of aluminum that have fused to the porcelain. When detonation occurs, part of the air/fuel mixture explodes instead of burning, the explosion is heard as a "metallic knock", this audible knock is the result of a sound shock-wave, this shock wave travels back and forth across the clearance volume "disrupting" the cooler boundary layer gases that cover the entire clearance volume area. This disruption allows "more" heat to be transferred into parts, especially, domes/piston tops,...along with the very rapid rise in pressure like a hammer blow, pistons can get torched with melted sides and holes !!! With the early signs of detonation, the shock-wave will also rattle rings causing the tiny amounts of oil that now gets by rings, to be fused to the white porcelain as tiny black specks, also fused as specks are soot that was clinging to clearance volume surfaces in the relatively "still-air" of the boundary layer. One step beyond the black specks, will be tiny specks/balls of aluminum coming off the pistons that will be fused to white porcelin,....the next step to be reached is occasional pieces of the porcelain being broken-off as detonation gets worse, ETC. Soon after that are holes, blown head gaskets, broken connecting rods, ETC.

NOTE> additional signs of beginning detonation are piston rings. By comparing ring's "free-diameter" to "out-of-box" free-diameters of new unused rings will reveals beginnings of detonation before much harm is caused !!! This is a result of the above previous explanation about heat being transferred more readily because the of the relatively insulating/cooler boundary layer being disrupted by the shock-wave. A piston ring is a simple spring, when a spring is over-heated it will loose tension.

Center Electrode = the very tiny sharply defined porcelain -"ditch" that encircles the center electrode, will also show up early signs of preignition/detonation and the wrong heat-range. Look for signs of the ditch beginning to be filled up with melted porcelain, you will need a 5x or 10x magnifying glass.
 
 

• The "Ground-Strap" = Heat Range
• The "Plug's Base-Ring" = Jetting
• The "Porcelain" = signs of preignition/detonation

courtesy of
Meaux Racing Heads
9827  LA  Hwy.  343
Abbeville,  Louisiana  70510
337-893-1541

 Thank You to Link for the following information.

***Remember*** to check for other relevant information in the columns and article tables.

ATTENTION READER:

If you enjoyed the information and article you just read be sure to check out our newly released book with even more exciting photo's and information:
How to Turbocharge and Tune your Engine

Follow Enginebasics on...

Want to know more about your particular Make and Model vehicle? All of these vehicles are covered in the tech, maintenance and repair articles found above. Enginebasics is the wiki or wikipedia of car part, repair, how to and tuning information. Let us be the class 101 for your automotive learning.

Individual Models

Below are just a few of the articles found here on enginebasics.com

Reading Spark Plugs	Camshaft Understanding	Engine Timing	Intake Runner Length	Exhaust Flow Tuning	Camshaft Timing	Engine Cooling Basics	Compression Testing	Forced Induction
Tuning A/F Ratio Basics	Intake Manifold Basics	A look at cooling mods	Camber Caster Basics	Sequential Vs Batch Injection	Fuel Pressure Regulator	EGT Vs A/F EFI Tuning	Engine Start Programming	What is a fuel Injector?
Brush vs Brushless Motors	4-stroke motor diagram	Crankshafts Basics	Automotive Relays	EFI Tuning Basic Thoery Guide	Understanding Electric Motors	Water Meth Injection	Intercooler Basics	e85 Basics
Water to Air Intercooling	Turbo Surge	EFI Air Intake Temp Tuning	Map vs. MAF Sensor EFI Tuning	Engine Start up tuning for EFI Cars	Building an EFI Surge Tank	Intercooler Efficency	Boost Controllers	Engine Oil Weights
Exhaust Cutout Basics	Cold Air Intake vs Short Ram	Engine HP and Torque Basics	Intercooler Sprayer Basics	Turbo Manifold Design Basics	Cryo Liquid Co2 Cooling	Oil Cooler Basics and Installation	Boost by Gear Tuning	Closed Loop vs Open Loop O2 tuning
Changing your own oil	Static Vs. Dynamic Compression	Air to Air Vs. Water to Air Intercoolers	Vented vs Recirculating Blow Off Valves	Engine Intake Exhaust Valves	Wiring a fuel pump relay	Synthetic vs Regular Oil	O2 Sensor Repair Fix	Embrace the TURBO LAG

**TO SUBMIT AN ARTICLE TO ENGINE BASICS PLEASE CLICK: CONTACT US!

Testimonials Page

“Thank you, for the info, on your site, on how to remove valve springs, and install stem seals, using normal shop tools. Info from every other site I looked at, only said how to do it using costly special tools. Thank you for showing the REAL easy way, and saving me some money.”   Joe S

“Hello there,
            Don’t have any questions, just wanted to say thanks for putting this info out there.  So much mis-information on forums, good to read some solid info. Peace” Jay R.

Privacy policy and terms of service

Advertise

Copyright 2010 EngineBasics.com: Engine Basics. All Rights Reserved

Enginebasics Google+ Page